The Bahrain International Circuit gets lit up with floodlights in the night as F1 cars roar through its tight turns and fast straights. With a decently competitive track like this, you are going to need the best F1 23 Bahrain setup to lead the pack.
This guide will give you all the settings you need to start dominating on this track, from tyre pressures and ride heights to brake pressures and suspension.
Best F1 23 Bahrain setup settings for dry and wet conditions
Bahrain has three long straights and multiple DRS zones. So, our F1 23 Bahrain setup build will focus on high speed and acceleration. We will also make room for handling some sharp turns that the track throws at you between the straights.
Note: Adjustments for wet conditions are provided along with dry settings. If no adjustment for wet is provided, then the dry settings will work just as well in wet.
While speed is our focus for this track, aerodynamics will be the department where we lean towards improving our turning capability. This is why we recommend medium to high aero values. It will ensure your car can quickly and smoothly rotate into turns, which will help preserve speed and mitigate the speed lost.
- Front Wing Aero: 34
- Rear Wing Aero: 24
- Front Wing Aero: 38
- Rear Wing Aero: 28
This transmission setting aims to have balanced stability while not sacrificing control. You can tweak these settings if you are used to higher or lower values, but these settings have proved to work for the best F1 23 Bahrain setup. If you are still wanting more stability out of your F1 car, try increasing these values by 5-8%.
- Differential Adjustment on-throttle: 55
- Differential Adjustment off-throttle: 50
While these settings can also be modified based on your style, the values here have been shown to give an optimal amount of tyre wear and stability in the long run. Other values may bring out more performance but won’t offer the same consistency. These values will ensure you get the perfect traction and grip through the corners and straights alike.
- Front camber: -2.80˚
- Rear Camber: -1.00˚
- Front Toe: 0.04˚
- Rear Toe: 0.14˚
A higher front suspension is the general setting to follow in F1 23. The values shown here work the best for this track specifically. These settings can be modified to a greater extent based on personal style, but make sure your rear suspension levels are always lower. Also, ensure your rear ride height is higher than the front.
- Front Suspension: 28
- Rear Suspension: 8
- Front Anti-Roll Bar: 6
- Rear Anti-Roll Bar: 1
- Front Ride Height: 33
- Rear Ride Height: 36
- Front Suspension: 32
- Rear Suspension: 11
- Front Anti-Roll Bar: 8
- Rear Anti-Roll Bar: 4
- Front Ride Height: 36
- Rear Ride Height: 40
A 100% brake pressure is essential for most setups, but if you are on wet or without ABS assist, you can set this value lower to about 95% for your F1 23 Bahrain setup. The front brake bias will ensure you dont lock up under high brake pressure. These settings are crucial as there are many hard breaks from high speed in Bahrain.
- Break Pressure: 100%
- Front Brake Bias: 53%
- Break Pressure: 95%
- Front Brake Bias: 55%
These tyre pressure settings are optimized for long runs at high speeds. It will ensure your tyre wear status is at the minimum with the maximum amount of performance you can get out of it. Managing your tyre wear can be a difficult task, so we recommend you follow these settings and try not to tweak them unless you know what you’re doing.
- Front Right Tyre Pressure: 22.5
- Front Left Tyre Pressure: 22.5
- Rear Right Tyre Pressure: 20.3
- Rear Left Tyre Pressure: 20.3
Bahrain is a fun mix of long straights along with sharp turns. The unique conditions due to the location of this race also pose a challenge on tyre wear, but with our F1 23 Bahrain setup, you will be on your way to the podium finish.